Dodge Challenger 2013 Specifiche

O W N E R ’ S M A N U A L2 0 1 0ChallengerS R T

Call TerminationTo end a call in progress, momentarily press thebutton. Only the active call(s) will be terminated and ifthere is a call on hold, it w

Uconnect™ Phone FeaturesLanguage SelectionTo change the language that the Uconnect™ Phone isusing:•Press the button to begin.•After the ⬙Ready⬙ prompt

Canada and 060 for Mexico). The number dialed maynot be applicable with the available cellular serviceand area.•If supported, this number may be progr

PagingTo learn how to page, refer to ⬙Working with AutomatedSystems.⬙ Paging works properly except for pagers ofcertain companies, which time out a li

The Uconnect™ Phone will then send the correspondingphone number associated with the phonebook entry, astones over the phone.NOTE:•You may not hear al

Dialing Using the Cellular Phone KeypadYou can dial a phone number with your cellular phonekeypad and still use the Uconnect™ Phone (while dialingvia

from your Uconnect™ Phone paired cellular phone to theUconnect™ Phone or vice versa, press thebuttonand say ⬙Transfer Call.⬙Connect or Disconnect Link

•The selected phone will be used for the next phonecall. If the selected phone is not available, theUconnect™ Phone will return to using the highestpr

Repeat the words and phrases when prompted by theUconnect™ Phone. For best results, the Voice Trainingsession should be completed when the vehicle is

•When navigating through an automated system suchas voice mail, or when sending a page, at the end ofspeaking the digit string, make sure to say ⬙Send

THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A Word About Your Keys ... 12▫ Wireless Ignition Node (WIN) ... 12▫ KeyFOB

•Performance, such as audio clarity, echo, and loudnessto a large degree rely on the phone and network, andnot the Uconnect™ Phone.•Echo at the phone

3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109

110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111

Voice CommandsPrimary Alternate(s)zeroonetwothreefourfivesixseveneightninestar (*)plus (+)pound (#)add locationallVoice CommandsPrimary Alternate(s)ca

Voice CommandsPrimary Alternate(s)languagelist nameslist phonesmobilemutemute offnew entrynopagerpair a phonephone pairing pairingphonebook phone book

General InformationThis device complies with Part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•

NOTE: If you do not say a command within a fewseconds, the system will present you with a list ofoptions.If you ever wish to interrupt the system whil

CommandsThe Voice Command system understands two types ofcommands. Universal commands are available at alltimes. Local commands are available if the s

Radio FMTo switch to the FM band, say “FM” or “Radio FM”. Inthis mode, you may say the following commands:•“Frequency” (to change the frequency)•“Next

▫ To Open The Trunk ... 25▫ Using The Panic Alarm ... 25▫ Programming Additional Transmitters ... 25▫ Transmitter Ba

MemoTo switch to the voice recorder mode, say “Memo”. Inthis mode, you may say the following commands:•“New Memo” (to record a new memo) — During ther

NOTE: Keep in mind that you have to press the VoiceCommandbutton first and wait for the beepbefore speaking the “Barge In” commands.Voice TrainingFor

switch is used to adjust the angle of the seatback. Pushforward or rearward on the switch to change the positionof the seatback.WARNING!Adjusting a se

Manual Front Seatback ReclineTo recline:1. Lean forward in the seat and lift the handle, then leanback to the desired position and release the handle.

Lumbar SupportThis feature allows you to increase or decrease theamount of lumbar support. Turn the control lever for-ward to increase and rearward to

WARNING!Driving a vehicle with the head restraints removed orimproperly adjusted could cause serious injury ordeath in the event of a collision. The h

Press the switch once to select High-level heat-ing. Press the switch a second time to selectLow-level heating. Press the switch a third timeto shut t

CAUTION!Repeated overheating of the seat could damage theheating element and/or degrade the material of theseat.Easy Entry SeatsPulling upward on the

Folding Rear SeatThe rear seatbacks can be folded forward to provide anadditional storage area. Pull on the loops shown in theillustration to fold dow

TO OPEN AND CLOSE THE HOODTwo latches must be released to open the hood.1. Pull the hood release lever located under the left sideof the instrument pa

▫ Supplemental Restraint System (SRS) -Airbags ... 48▫ Airbag Deployment Sensors And Controls . . . 54▫ Event Data Recorder (

CAUTION!To prevent possible damage, do not slam the hood toclose it. Lower the hood until it is open approxi-mately 6 in (15 cm), and then drop it. Th

Rotate the headlight switch clockwise to the first detentfor parking light and instrument panel light operation.Turn it to the second detent for headl

To activate the delay feature, place the ignition in the OFFposition while the headlights are still on. Then, turn offthe headlights within 45 seconds

An indicator light in the instrument cluster illuminateswhen the fog lights are turned on.NOTE: The fog lights will operate with the low beamheadlight

NOTE:•If either light remains on and does not flash, or there isa very fast flash rate, check for a defective outside lightbulb. If an indicator fails

Interior LightsThe interior lights come on when a door is opened.To protect the battery, the interior lights will turn offautomatically 10 minutes aft

Interior Light Defeat (OFF)Rotate the dimmer control to the extreme bottom offposition. The interior lights will remain off when thedoors are open.Par

CAUTION!Turn the windshield wipers off when drivingthrough an automatic car wash. Damage to the wind-shield wipers may result if the wiper switch is l

WARNING!Sudden loss of visibility through the windshieldcould lead to a collision. You might not see othervehicles or other obstacles. To avoid sudden

To unlock the steering column, pull the control handleoutward. To tilt the steering column, move the steeringwheel upward or downward as desired. To l

A WORD ABOUT YOUR KEYSYour vehicle uses a keyless ignition system. This systemconsists of a Key Fob with Remote Keyless Entry (RKE)transmitter and a W

ELECTRONIC SPEED CONTROLWhen engaged, Electronic Speed Control takes over theaccelerator operation at speeds greater than 25 mph(40 km/h).The Electron

WARNING!Leaving the Electronic Speed Control system onwhen not in use is dangerous. You could accidentallyset the system or cause it to go faster than

previous set speed. To do so, push the lever upward toRESUME ACCEL and release. Then remove your footfrom the accelerator pedal.To Vary the Speed Sett

On steep hills, a greater speed loss or gain may occur, soit may be preferable to drive without Electronic SpeedControl.WARNING!Electronic Speed Contr

These lights also turn on when a door is opened, whenthe UNLOCK button on the Remote Keyless Entry (RKE)transmitter is pressed, or when the dimmer con

WARNING!•Your motorized door or gate will open and closewhile you are training the Universal Transceiver.Do not train the transceiver if people, pets

2. Place the handheld transmitter 1 to 3 in (3 to 8 cm)from the HomeLink威 buttons while keeping the EVICdisplay in view.For optimal training, point th

This can usually be found where the hanging antennawire is attached to the garage door opener motor (it isNOT the button normally used to open and clo

Gate Operator/Canadian ProgrammingCanadian radio-frequency laws require transmitter sig-nals to “time-out” (or quit) after several seconds oftransmiss

Reprogramming A Single HomeLink姞 ButtonTo reprogram a channel that has been previously trained,follow these steps:1. Place the ignition in the RUN pos

Key FobThe Key Fob operates the ignition switch. It also containsthe Remote Keyless Entry (RKE) transmitter and anemergency key, which stores in the r

General InformationThis device complies with FCC rules Part 15 and IndustryCanada RSS-210. Operation is subject to the followingtwo conditions:1. This

WARNING!•Never leave children in a vehicle with the key inthe ignition switch (or with the ignition in theAccessory or Run position, for vehicles equi

Opening Sunroof — ExpressPress the switch rearward and release, and the sunroofwill open automatically from any position. The sunroofwill open fully a

Venting Sunroof — ExpressPress and release the Vent button in the center of theswitch, and the sunroof will open to the vent position.This is called “

ELECTRICAL POWER OUTLETSThere are two 12 Volt (13 Amp) electrical power outletson this vehicle. Both of the outlets are protected by a fuse.The front

WARNING!To avoid serious injury or death:•Only devices designed for use in this type ofoutlet should be inserted into any 12 Volt outlet.•Do not touch

CAUTION! (Continued)•Power outlets are designed for accessory plugsonly. Do not insert any other object in the poweroutlet as this will damage the out

Rear CupholdersThe rear seat cupholders are located in the center armrestbetween the rear seats. The cupholders are positionedforward in the armrest a

CONSOLE FEATURESSliding Center Console ArmrestThe center console armrest slides forward with threedetents to provide flexibility for comfort, cupholde

REAR WINDOW FEATURESRear Window DefrosterThe rear window defroster button is located on theclimate control (Mode) knob. Press this button toturn on th

To remove the emergency key, slide the mechanical latchat the top of the Key Fob sideways with your thumb andthen pull the key out with your other han

CAUTION!Failure to follow these cautions can cause damage tothe heating elements:•Use care when washing the inside of the rearwindow. Do not use abras

UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 Instrument Panel Features ... 162䡵 Instrument Cluster ... 163䡵 Instrument Cl

䡵 Media Center 730N/430 (RER/RBZ) —AM/FM Stereo Radio And CD/DVD/HDD/NAV — If Equipped ... 192▫ Operating Instructions — Voice Comman

▫ Play Mode ... 219▫ List Or Browse Mode ... 221䡵 Uconnect™ Multimedia (Satellite Radio) — IfEquipped (REN/REQ/RER

INSTRUMENT PANEL FEATURES1 — Air Outlets 5 — Heated Seat Switch 9 — Ignition Switch2 — Instrument Cluster 6 — ESP OFF Switch 10 — Trunk Release Button

INSTRUMENT CLUSTER4UNDERSTANDING YOUR INSTRUMENT PANEL 163

INSTRUMENT CLUSTER DESCRIPTIONS1. Fuel GaugeThe pointer shows the level of fuel in the fuel tank whenthe ignition switch is in the ON/RUN position.2.

7. Electronic Throttle Control (ETC) Warning LightThis light will turn on briefly as a bulb checkwhen the ignition switch is placed in ON/RUN. This li

CAUTION!Driving with a hot cooling system could damageyour vehicle. If the temperature gauge reads 240°F(116°C) or greater, pull over and stop the veh

NOTE:•A continuous chime will sound if the vehicle is drivenmore than 1 mile (1.6 km) with either turn signal on.•Check for an inoperative outside lig

WARNING!•Never leave children alone in a vehicle. Leavingunattended children in a vehicle is dangerous for anumber of reasons. A child or others could

the BAS system. If this light remains on after severalignition cycles, and the vehicle has been driven severalmiles (kilometers) at speeds greater tha

17. Shift Lever Indicator — Automatic TransmissionOnlyThe Shift Lever Indicator is self-contained within theinstrument cluster. It displays the gear p

press the TRIP ODOMETER button to turn off themessage. If the problem continues, the message willappear the next time the vehicle is started.A loose,

WARNING!Driving a vehicle with the brake light on is danger-ous. Part of the brake system may have failed. It willtake longer to stop the vehicle. You

vehicle placard or tire inflation pressure label, you shoulddetermine the proper tire inflation pressure for thosetires.)As an added safety feature, y

tires or wheels on your vehicle, to ensure that thereplacement or alternate tires and wheels allow the TPMSto continue to function properly.CAUTION!Th

24. Low Fuel LightThis light will turn on and a single chime willsound when the fuel level drops to 1/8 tank.25. Malfunction Indicator Light (MIL)The

ELECTRONIC VEHICLE INFORMATION CENTER(EVIC)The Electronic Vehicle Information Center (EVIC) fea-tures a driver-interactive display that is located in

•Surround Sound modes (if equipped with Driver-Selectable Surround [DSS])•Performance FeaturesThe system allows the driver to select information bypre

Electronic Vehicle Information Center (EVIC)DisplaysWhen the appropriate conditions exist, the EVIC displaysthe following messages:•Turn Signal On (wi

SENTRY KEY姞The Sentry Key威 Immobilizer System prevents unauthor-ized vehicle operation by disabling the engine. Thesystem does not need to be armed or

•Right Front Low Pressure (with a single chime)•Right Rear Low Pressure (with a single chime)•Check TPM System (with a single chime)•ESP Off•Check Gas

Unless reset, this message will continue to display eachtime you turn the ignition switch to the ON/RUNposition. To turn off the message temporarily,

history information will be erased, and the averaging willcontinue from the last fuel average reading before thereset.Distance To Empty (DTE)Shows the

To Reset The DisplayReset will only occur while a resettable function is beingdisplayed. Press and release the FUNCTION SELECTbutton once to clear the

The Performance Features include the following:•0-60 mph (0-100 km/h)•Braking Distance•1/8 Mile•1/4 Mile•Instantaneous G-Force•Peak G-Force•Digital Sp

Braking DistanceWhen selected, this screen displays the vehicle’s brakingdistance and the speed at which the brake pedal wasdepressed.•This feature wi

•The time and speed will continue to display until theFUNCTION SELECT button is pressed.•Pressing the FUNCTION SELECT button will clear thecurrent run

Keyless Enter-N-Go Display — If EquippedWhen the ENGINE START/STOP button is pressed tochange ignition switch positions, the Keyless Enter-N-Goicon mo

•Video Surround•Audio SurroundWhile in the Surround Sound menu, press the FUNC-TION SELECT button to change surround modes. TheVideo Surround Mode wil

2. Press and hold the HOME button for approximatelytwo seconds.3. Press the SCROLL button until “Calibrate Compass”displays in the EVIC.4. Press and r

Replacement KeysNOTE: Only Key Fobs that are programmed to thevehicle electronics can be used to start and operate thevehicle. Once a Key Fob is progr

2. Press and hold the HOME button for approximatelytwo seconds.3. Press the SCROLL button until “Compass Variance”message and the last variance zone n

FUNCTION SELECT button while in this display toselect English, Espanol, or Francais. Then, as you con-tinue, the information will display in the selec

lock/unlock feature. To make your selection, press andrelease the FUNCTION SELECT button until “ON” or“OFF” appears.Flash Lights with Remote Key LockW

Operating” for system function and operating informa-tion. To make your selection, press and release theFUNCTION SELECT button until “ON” or “OFF”appe

MEDIA CENTER 730N/430 (RER/RBZ) — AM/FMSTEREO RADIO AND CD/DVD/HDD/NAV — IFEQUIPPEDNOTE: The sales code is located on the lower right sideof the unit’

displayed. To move the minute backward, touch thescreen where the word “Min” with the arrow pointingdownward is displayed.5. To save the new time sett

3. Touch the screen where the words “Set Time Zone” aredisplayed. The time zone selection menu will appear onthe screen.4. Select a time zone by touch

6. To save the new time setting, touch the screen wherethe word “Save” is displayed.Changing Daylight Savings TimeWhen selected, this feature will dis

4. Touch the screen where the words “Set Time Zone” aredisplayed. The time zone selection menu will appear onthe screen.5. Select a time zone by touch

Power Switch/Volume Control (Rotary)Push the ON/VOLUME control knob to turn on theradio. Push the ON/VOLUME control knob a secondtime to turn off the

291686.ps 11Y532-126-AA Chrysler 1" gutter 07/14/2010 08:26:13VEHICLES SOLD IN CANADAWith respect to any Vehicles Sold in Canada, the nameChrysle

•This device must accept any interference that may bereceived, including interference that may cause unde-sired operation.VEHICLE SECURITY ALARMThe Ve

RW/FFPressing the RW (Rewind) or FF (Fast Forward) buttonscauses the tuner to search for the next frequency in thedirection of the arrows. This featur

SET/RND Button — To Set the PushbuttonMemoryWhen you are receiving a station that you wish tocommit to pushbutton memory, press the SET/RNDbutton. The

discs (CD-RW), compact discs with MP3 tracks andmultisession compact discs with CD and MP3 tracks.Inserting Compact Disc(s)Gently insert one CD into t

If you have ejected a disc and have not removed it within10 seconds, it will be reloaded. If the CD is not removed,the radio will reinsert the CD but

Notes on Playing MP3 FilesThe radio can play MP3 files; however, acceptable MP3file recording media and formats are limited. Whenwriting MP3 files, pa

Discs created with an option such as ⬙keep disc open afterwriting⬙ are most likely multisession discs. The use ofmultisession for CD audio or MP3 play

Playback of MP3 FilesWhen a medium containing MP3 data is loaded, theradio checks all files on the medium. If the mediumcontains a lot of folders or f

MEDIA CENTER 130 (RES/RSC) — AM/FMSTEREO RADIO WITH CD PLAYER (MP3 AUXJACK) AND SIRIUS RADIONOTE: The radio sales code is located on the lower rightsi

SEEK ButtonsPress and release the SEEK buttons to search for the nextlistenable station in AM/FM mode. Press the right switchto seek up and the left s

Clock Setting Procedure1. Press and hold the TIME button until the hours blink.2. Adjust the hours by turning the right side TUNE/SCROLL control knob.

Vehicles Equipped with Keyless Enter-N-GoPress the Keyless Enter-N-Go Start/Stop button until theElectronic Vehicle Information Center (EVIC) indicate

Setting the Tone, Balance, and FadePush the rotary TUNE/SCROLL control knob and BASSwill display. Turn the TUNE/SCROLL control knob tothe right or lef

Toggle the MUSIC TYPE button to select the followingformat types:Program Type16-DigitCharacter DisplayNo program typeor undefinedNoneAdult Hits Adlt H

By pressing the SEEK button when the Music Type iconis displayed, the radio will be tuned to the next frequencystation with the same selected Music Ty

You may add a second station to each pushbutton byrepeating the above procedure with this exception: Pressthe SET/RND button twice and SET 2 will show

If you insert a disc with the ignition ON/RUN and theradio ON, the unit will switch from radio to CD modeand begin to play when you insert the disc. T

the current selection. Pressing and holding the SEEKbutton will allow faster scrolling through the tracks inCD and MP3 modes.TIME ButtonPress this but

Supported Medium Formats (File Systems)The medium formats supported by the radio are ISO 9660Level 1 and Level 2 and includes the Joliet extension.Whe

Supported MP3 File FormatsThe radio will recognize only files with the *.MP3 exten-sion as MP3 files. Non-MP3 files named with the *.MP3extension may

Loading times for playback of MP3 files may be affectedby the following:•Media - CD-RW media may take longer to load thanCD-R media•Medium formats - M

Operation Instructions - Auxiliary ModeThe auxiliary (AUX) jack is an audio input jack whichallows the user to plug in a portable device such as anMP3

If the Vehicle Security Alarm is armed and the batterybecomes disconnected, the Vehicle Security Alarm willremain armed when the battery is reconnecte

This feature allows an iPod威 to be plugged into thevehicle’s sound system through a 16–pin connector, usingthe provided interface cable.UCI supports M

Using This FeatureBy using the provided connection cable to connect aniPod威 to the vehicle’s UCI 16–pin connector port:•The iPod威 audio can be played

•Jump backward in the current track by pressing andholding the << RW button. Holding the << RWbutton long enough will jump to the beginnin

Shuffle OFF modes for the iPod威.IftheRND icon isshowing on the radio display, then the shuffle mode isON.List Or Browse ModeDuring Play mode, pressing

•Pressing a PRESET button will display the currentlist on the top line and the first item in that list onthe second line.•To Exit List mode without se

Uconnect™ Multimedia (SATELLITE RADIO) — IFEQUIPPED (REN/REQ/RER/RES RADIOS ONLY)Satellite radio uses direct satellite-to-receiver broadcast-ing techn

Sirius ID number will display. The Sirius ID numberdisplay will time out in two minutes. Press any button onthe radio to exit this screen.ESN/SID Acce

Operating Instructions - Uconnect™ Multimedia(Satellite) ModeNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.SEEK Butt

MUSIC TYPE ButtonPressing this button once will turn on the Music Typemode for five seconds. Pressing the MUSIC TYPE buttonor turning the TUNE/SCROLL

pushbutton memory. The channels stored in SET 2memory can be selected by pressing the pushbuttontwice.Every time a preset button is used, a correspond

REMOTE KEYLESS ENTRY (RKE)The RKE system allows you to lock or unlock the doors,open the trunk, or activate the Panic Alarm from dis-tances up to appr

“Audio Surround” is optimized for front seat passengers forany audio source. This surround effect is available for audiofrom any source – AM/FM/CD/ Sa

Vehicles equipped with steering wheel-mounted buttonsare also equipped with the Electronic Vehicle InformationCenter (EVIC). The EVIC features a drive

CD/DVD DISC MAINTENANCETo keep a CD/DVD in good condition, take the followingprecautions:1. Handle the disc by its edge; avoid touching thesurface.2.

CLIMATE CONTROLSManual Air Conditioning and Heating SystemThe controls for the manual system in this vehicle containa series of outer rotary dials and

Temperature ControlUse this control to regulate the tem-perature of the air inside the passengercompartment. Rotating the knob coun-terclockwise, from

Bi-Level ModeAir is directed through the panel and floor outlets.NOTE: There is a difference in temperature (in anyconditions other than full cold or

NOTE:•If the RECIRCULATION button is pressed when thesystem is in MIX, DEFROST, or FLOOR mode theRECIRCULATION LED indicator will flash 3 timesand the

Max A/CFor maximum cooling use the A/C and RECIRCULA-TION mode buttons at the same time.Remote Start — If EquippedDuring remote start operation, the c

Operating TipsNOTE: Refer to the chart at the end of this section forsuggested control settings for various weather condi-tions.Summer OperationThe en

Side Window DemistersA side window demister outlet is located at each end ofthe instrument panel. These non-adjustable outlets directair toward the si

Remote Key Unlock, Driver Door/All Doors FirstThis feature lets you program the system to unlock eitherthe driver’s door or both doors on the first pr

Control Setting Suggestions for Various Weather Conditions238 UNDERSTANDING YOUR INSTRUMENT PANEL

STARTING AND OPERATINGCONTENTS䡵 Starting Procedures ... 243▫ Manual Transmission – If Equipped ... 243▫ Automatic Transmission –

▫ Five-Speed Automatic Transmission ... 260▫ Gear Ranges ... 260䡵 AutoStick威 ... 264▫ Operation ...

䡵 Tire Safety Information ... 286▫ Tire Markings ... 286▫ Tire Terminology And Definitions ... 291▫ Tire Loadi

▫ Fuel System Cautions ... 313▫ Carbon Monoxide Warnings ... 314䡵 Adding Fuel ... 315▫ Fuel Filler Cap (G

STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust theinside and outside mirrors, fasten your seat belt, and ifpresent, instruc

WARNING!Do not attempt to push or tow your vehicle to get itstarted. Unburned fuel could enter the catalytic con-verter and once the engine has starte

Do not press the accelerator. Use the Fob with IntegratedKey to briefly turn the ignition switch to the STARTposition and release it as soon as the st

NOTE: The ENGINE START/STOP button should onlybe removed or inserted with the ignition in the OFFposition.Normal StartingUsing the ENGINE START/STOP B

2. The ignition switch will return to the OFF position.3. If the shift lever is not in PARK, the ENGINE START/STOP button must be held for two seconds

•When not using the EVIC, perform the followingsteps:1. Press and hold the UNLOCK button on a programmedRKE transmitter for at least 4 seconds, but no

•If the vehicle speed is above 5 mph (8 km/h), theENGINE START/STOP button must be held for twoseconds before the engine will shut off. The ignitionsw

If Engine Fails To StartWARNING!•Never pour fuel or other flammable liquids into thethrottle body air inlet opening in an attempt to startthe vehicle.

the way to the floor and hold it, then press and hold theENGINE START/STOP button for no more than 15 sec-onds. Release the accelerator pedal and the

The engine block heater must be plugged in at least onehour to have an adequate warming effect on the engine.WARNING!Remember to disconnect the engine

NOTE: During cold weather, you may experience in-creased effort in shifting until the transmission fluidwarms up. This is normal.ShiftingFully press t

CAUTION!Always make sure the vehicle comes to a completestop before shifting into REVERSE. Failure to do somay result in transmission damage.You must

with the clutch engaged (clutch pedal released), but itmay also be heard when driving at low engine RPM.Also, this may be more noticeable when the tra

CAUTION!•If you skip more than one gear while downshift-ing or downshift at too high an engine speed, youcould damage the engine, transmission, or clu

WARNING!It is dangerous to move the shift lever out of PARK orNEUTRAL if the engine speed is higher than idlespeed. If your foot is not firmly on the

•The electronically-controlled transmission provides aprecise shift schedule. The transmission electronics areself-calibrating. Therefore, the first f

Sound Horn with Remote Key LockThis feature will cause the horn to chirp when the doorsare locked with the RKE transmitter. This feature can beturned

Over-Temperature ModeThe transmission electronics constantly monitor thetransmission oil temperature. If the transmission exceedsnormal operating temp

1. Turn the ignition switch to the ACC or ON position(RUN position with Keyless Go™) without starting theengine.2. Firmly set the parking brake.3. Pre

With Keyless Go™If the engine is running, press the START/STOP button toturn it off. Release the brake pedal and press the START/STOP button once or t

When parking on a flat surface, place the shift lever in thePARK position first, and then apply the parking brake.When parking on a hill, it is import

REVERSEThis range is used for moving the vehicle rearward.Always stop before moving the shift lever to REVERSE.NEUTRALThis range is used when the vehi

under heavy loading conditions (in hilly terrain, travel-ing into strong head winds, or while towing heavytrailers, use the AutoStick威 mode and select

NOTE: Even if the transmission can be reset, we recom-mend that you visit your authorized dealer at yourearliest possible convenience. Your authorized

You can shift in or out of the AutoStick威 mode at anytime without taking your foot off the accelerator pedal.When you wish to engage AutoStick威, simpl

WARNING!Rapid acceleration on slippery surfaces is dangerous.Unequal traction can cause sudden pulling of the rearwheels. You could lose control of th

CAUTION!•Due to lower ground clearance, driving your ve-hicle up steep driveways, approach ramps or nearparking blocks may cause damage to the frontfa

To Open The TrunkPress the TRUNK button on the RKE transmitter twotimes within five seconds to open the trunk.Using The Panic AlarmTo turn the Panic A

CAUTION!•Always check the depth of the standing waterbefore driving through it. Never drive throughstanding water that is deeper than the bottom ofthe

WARNING!•Driving through standing water limits your vehi-cle’s traction capabilities. Do not exceed 5 mph(8 km/h) when driving through standing water.

system. This noise should be considered normal, and itdoes not in any way damage the steering system.WARNING!Continued operation with reduced power st

If necessary, add fluid to restore to the proper indicatedlevel. With a clean cloth, wipe any spilled fluid from allsurfaces. Refer to “Fluids, Lubric

Manual Transmission – If EquippedThe foot operated parking brake is positioned below thelower left corner of the instrument panel. To release theparki

WARNING!•Never use the PARK position as a substitute forthe parking brake. Always apply the parkingbrake fully when parked to guard against vehiclemov

BRAKE SYSTEMYour vehicle is equipped with dual hydraulicbrake systems. If either of the two hydraulicsystems loses normal capability, the remainingsys

You also may experience the following when the brakesystem goes into Anti-Lock:•The ABS motor running (it may continue to run for ashort time after th

WARNING! (Continued)•The Anti-Lock Brake System (ABS) cannot preventthe natural laws of physics from acting on thevehicle, nor can it increase braking

If both the “Brake Warning Light” and the “ABS WarningLight” remain on, the ABS and EBD systems are notfunctioning. Immediate repair to the ABS system

2. Remove and replace the battery. When replacing thebattery, match the + sign on the battery to the + sign onthe inside of the battery clip, located

Traction Control System (TCS)This system monitors the amount of wheel spin of eachdriven wheel. If wheel spin is detected, brake pressure isapplied to

WARNING!The BAS cannot prevent the natural laws of physicsfrom acting on the vehicle, nor can it increase thetraction afforded by prevailing road cond

WARNING!There may be situations on minor hills (i.e., less than8%), with a loaded vehicle, or while pulling a trailer,when the system will not activat

8. Rotate the steering wheel back to center and then anadditional half-turn to the right.9. Turn the ignition switch to the OFF position and thenback

accelerator and apply as little throttle as possible. Be sureto adapt your speed and driving to the prevailing roadconditions.WARNING!The ESP cannot p

switch and the “ESP/TCS Indicator Light” will illumi-nate. To turn the ESP ON again, momentarily press the“ESP OFF” switch and the “ESP/TCS Indicator

“Electronic Vehicle Information Center (EVIC)” in “Un-derstanding Your Instrument Panel” for further informa-tion. To turn ESP ON again, momentarily p

Synchronizing ESPThe Malfunction Indicator Light for the ESP iscombined with BAS indicator. If the powersupply is interrupted (battery disconnected or

NOTE:•The “ESP/TCS Indicator Light” and the “ESP/BASMalfunction Indicator Light” will turn on momen-tarily each time the ignition switch is turned ON.

NOTE:•P (Passenger) - Metric tire sizing is based on U.S.design standards. P-Metric tires have the letter “P”molded into the sidewall preceding the si

REMOTE STARTING SYSTEMThis system uses the Remote Keyless Entry(RKE) transmitter to start the engine conve-niently from outside the vehicle while stil

=Tire Sizing ChartTIRE SIZING TERMSSize Designation:P = Passenger Car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger Car tire bas

TIRE SIZING TERMSService Description:95 = Load Index— A numerical code associated with the maximum load a tire can carryH = Speed Symbol— A symbol ind

Tire Identification Number (TIN)The TIN may be found on one or both sides of the tire,however, the date code may only be on one side. Tireswith white

Tire Terminology and DefinitionsTerm DefinitionB-Pillar The vehicle B-Pillar is a structural member of the body locatedbetween the front and rear door

Tire Loading and Tire PressureTire Placard LocationNOTE: The proper cold tire inflation pressure is listedon the driver’s side B-Pillar.Tire and Loadi

axles must not be exceeded. For further information onGAWRs, vehicle loading, and trailer towing, refer to“Vehicle Loading” in this section.To determi

NOTE:•The following table shows examples on how to calcu-late total load, cargo/luggage, and towing capacitiesof your vehicle with varying seating con

5STARTING AND OPERATING 295

WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti

WARNING! (Continued)•Unequal tire pressures from one side of the ve-hicle to the other can cause the vehicle to drift tothe right or left.•Always driv

TABLE OF CONTENTSSECTION PAGE1INTRODUCTION...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE...

To Enter Remote Start ModePress and release the REMOTE START buttonon the RKE transmitter twice, within five sec-onds. The parking lights will flash a

CAUTION!After inspecting or adjusting the tire pressure, al-ways reinstall the valve stem cap. This will preventmoisture and dirt from entering the va

loading may be required for high-speed vehicle opera-tion. Refer to original equipment or an authorized tiredealer for recommended safe operating spee

WARNING!Fast spinning tires can be dangerous. Forces gener-ated by excessive wheel speeds may cause tire dam-age or failure. A tire could explode and

Life Of TireThe service life of a tire is dependent upon varyingfactors including, but not limited to:•Driving style•Tire pressure•Distance drivenWARN

WARNING!•Do not use a tire, wheel size or rating other thanthat specified for your vehicle. Some combinationsof unapproved tires and wheels may change

SNOW TIRESSome areas of the country require the use of snow tiresduring the winter. Standard tires are of the all season typeand satisfy this requirem

Tire Rotation – Four Season/RSA TiresThe suggested rotation method for vehicles equippedwith all season tires is the “forward-cross” as shown inthe fo

TIRE PRESSURE MONITOR SYSTEM (TPMS)The Tire Pressure Monitor System (TPMS) will warn thedriver of a low tire pressure based on the vehicle recom-mende

For example, your vehicle may have a recommendedcold (parked for more than three hours) placard pressureof 30 psi (207 kPa). If the ambient temperatur

NOTE:•The TPMS is not intended to replace normal tire careand maintenance or to provide warning of a tire failureor condition.•The TPMS should not be

equipped). Then, prior to the end of the 15 minute cycle,press and release the START/STOP button. If theSTART/STOP button is not present, insert the K

•Various TPMS messages, which display in the Elec-tronic Vehicle Information Center (EVIC), and•TPM Telltale LightTire Pressure Monitoring Low Pressur

will turn off. The vehicle may need to be driven for up to20 minutes above 15 mph (25 km/h) in order for theTPMS to receive this information.Check TPM

1. Signal interference due to electronic devices or drivingnext to facilities emitting the same radio frequencies asthe TPM sensors.2. Installing afte

Light spark knock at low engine speeds is not harmful toyour engine. However, continued heavy spark knock athigh speeds can cause damage and immediate

CAUTION!Do not use gasolines containing Methanol or E85Ethanol. Use of these blends may result in startingand driveability problems and may damage cri

MMT In GasolineMMT is a manganese-containing metallic additive that isblended into some gasoline to increase octane. Gasolineblended with MMT provides

CAUTION! (Continued)•An out-of-tune engine or certain fuel or ignitionmalfunctions can cause the catalytic converter tooverheat. If you notice a punge

WARNING! (Continued)•Guard against carbon monoxide with propermaintenance. Have the exhaust system inspectedevery time the vehicle is raised. Have any

CAUTION!•Damage to the fuel system or emissions controlsystem could result from using an improper fueltank filler tube cap (gas cap).•A poorly fitting

•When the fuel nozzle “clicks” or shuts off, the fueltank is full.Loose Fuel Filler Cap MessageIf the vehicle diagnostic system determines that the fu

If the door lock knob is down when you shut the door,the door will lock. Therefore, make sure the key is notinside the vehicle before closing the door

•Type of Vehicle•Month Day and Hour of Manufacture (MDH)The bar code allows a computer scanner to read the VIN.Gross Vehicle Weight Rating (GVWR)The G

Figure out the weight on the front and rear of the vehicleseparately. It is important that you distribute the loadevenly over the front and rear axles

The parking brake must be firmly engaged and thewheels chocked during driveshaft removal and installa-tion. The parking brake must remain engaged unle

WHAT TO DO IN EMERGENCIESCONTENTS䡵 Hazard Warning Flasher ... 322䡵 If Your Engine Overheats ... 322䡵 TIREFIT Kit ...

HAZARD WARNING FLASHERThe Hazard Warning flasher switch is located in theswitch bank near the bottom center of the instrumentpanel.Press the switch to

•You can also turn the temperature control to maximumheat, the mode control to floor and the blower controlto high. This allows the heater core to act

TIREFIT StorageThe TIREFIT kit is located in the trunk.TIREFIT Kit Components and Operation1. Sealant Bottle2. Deflation Button — If Equipped3. Pressu

5. Mode Select Knob6. Sealant Hose (Clear with Yellow Cap)7. Air Pump Hose (Black)8. Power PlugUsing the Mode Select Knob and HosesYour TIREFIT kit ma

TIREFIT Usage Precautions•Replace the TIREFIT Sealant Bottle (1) and SealantHose (6) prior to the expiration date (printed on thebottle label) to assu

WARNING! (Continued)•Do not use TIREFIT or drive the vehicle under thefollowing circumstances:−If the cut or puncture in the tire tread is approxi-mat

If you press the power door lock switch while the KeyFob is in the ignition, and either door is open, the powerlocks will not operate. This prevents y

WARNING! (Continued)•TIREFIT Sealant solution contains latex. In case ofallergic reaction or rash, consult a physician im-mediately. Keep TIREFIT out

3. Uncoil the Sealant Hose (6) and then remove theyellow cap from the fitting at the end of the hose.4. Place the TIREFIT kit flat on the ground next

2. Connect the Power Plug (8) to a different 12 Voltpower outlet in your vehicle or another vehicle, if avail-able. Make sure the engine is running be

If the tire inflates to the recommended pressure or is atleast 26 psi (1.8 Bar) pressure within 15 minutes:1. Press the Power Button (4) to turn off t

WARNING!TIREFIT is not a permanent flat tire repair. Have thetire inspected and repaired or replaced after usingTIREFIT. Do not exceed 55 mph (88 km/h

4. Have the tire inspected and repaired or replaced at theearliest opportunity at an authorized dealer or tire ser-vice center.5. Replace the Sealant

JUMP-STARTING PROCEDURESIf your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery inanother vehicle o

Remote Battery PostsWARNING!•Take care to avoid the radiator cooling fan when-ever the hood is raised. It can start anytime theignition switch is on.

3. If using another vehicle to jump-start the battery, parkthe vehicle within the jumper cables reach, set theparking brake and make sure the ignition

WARNING!Do not connect the cable to the negative post (-) of thedischarged battery. The resulting electrical sparkcould cause the battery to explode a

6. The vehicle speed is 0 mph (0 km/h)Automatic Unlock Doors on Exit ProgrammingThe Automatic Unlock Doors On Exit feature can beenabled or disabled.

FREEING A STUCK VEHICLEIf your vehicle becomes stuck in mud, sand, or snow, itcan often be moved by a rocking motion. Turn yoursteering wheel right an

WARNING!Fast spinning tires can be dangerous. Forces gener-ated by excessive wheel speeds may cause damage, oreven failure, of the axle and tires. A t

If the transmission is not operative or if the vehicle is tobe towed more than 15 miles (24 km) or faster than30 mph (48 km/h), the vehicle must be tr

MAINTAINING YOUR VEHICLECONTENTS䡵 Engine Compartment — 6.1L ... 343䡵 Onboard Diagnostic System — OBD II ... 344▫ Loose Fuel Filler Cap ..

▫ Clutch Hydraulic System (ManualTransmission) – If Equipped ... 366▫ Manual Transmission – If Equipped ... 366▫ Automatic Transmission

ENGINE COMPARTMENT — 6.1L1 — Remote Jump Start (Positive Battery Post) 6 — Power Steering Fluid Reservoir2 — Integrated Power Module 7 — Air Cleaner F

ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor

Trip Odometer button to turn off the message. If theproblem continues, the message will appear the next timethe vehicle is started.A loose, improperly

5. Approximately 15 seconds later, one of two things willhappen:a. The MIL will flash for about 10 seconds and thenreturn to being fully illuminated u

DEALER SERVICEYour authorized dealer has the qualified service person-nel, special tools, and equipment to perform all serviceoperations in an expert

WINDOWSPower WindowsThe window controls on the driver’s door control both ofthe door windows.There is a single window control on the passenger’s doort

CAUTION! (Continued)•Your vehicle has been built with improved fluidsthat protect the performance and durability ofyour vehicle and also allow extende

NOTE: Under no circumstances should oil changeintervals exceed 6,000 miles (10 000 km) or six months,whichever occurs first.Engine Oil SelectionFor be

environment. Contact your authorized dealer, servicestation, or governmental agency for advice on how andwhere used oil and oil filters can be safely

Engine Air Cleaner Filter SelectionThe quality of replacement engine air cleaner filtersvaries considerably. Only high quality filters should beused t

WARNING!•Battery fluid is a corrosive acid solution and canburn or even blind you. Do not allow battery fluidto contact your eyes, skin, or clothing.

Air Conditioner MaintenanceFor best possible performance, your air conditionershould be checked and serviced by an authorized dealerat the start of ea

Refrigerant Recovery and RecyclingR-134a Air Conditioning Refrigerant is a hydrofluoro-carbon (HFC) that is endorsed by the EnvironmentalProtection Ag

Operation of the wipers on dry glass for long periodsmay cause deterioration of the wiper blades. Always usewasher fluid when using the wipers to remo

WARNING!Commercially available windshield washer solventsare flammable. They could ignite and burn you. Caremust be exercised when filling or working

CAUTION!•The catalytic converter requires the use of un-leaded fuel only. Leaded gasoline will destroy theeffectiveness of the catalyst as an emission

AUTO-Down FeatureThe driver’s door power window switch and passengerdoor power window switch have an AUTO-down fea-ture. Press the window switch to th

To minimize the possibility of catalytic converter dam-age:•Do not shut off the engine or interrupt the ignition,when the transmission is in gear and

Coolant ChecksCheck the engine coolant (antifreeze) protection every12 months (before the onset of freezing weather, whereapplicable). If coolant is d

CAUTION!•Mixing of coolants other than specified HOATengine coolants may result in engine damage andmay decrease corrosion protection. If a non-HOATco

•Mix a minimum solution of 50% HOAT engine coolantand distilled water. Use higher concentrations (not toexceed 70%) if temperatures below −34°F (−37°C

WARNING! (Continued)•Do not use a pressure cap other than the onespecified for your vehicle. Personal injury or en-gine damage may result.Disposal of

humidity accumulating on the radiator and being vapor-ized when the thermostat opens, allowing hot coolant toenter the radiator.If an examination of y

Brake SystemIn order to assure brake system performance, all brakesystem components should be inspected periodically.Refer to “Maintenance Schedule” f

WARNING!•Use only manufacturer’s recommended brakefluid. Refer to “Fluids, Lubricants, and GenuineParts” in “Maintaining Your Vehicle” for furtherinfo

WARNING! (Continued)•Do not allow petroleum based fluid to contami-nate the brake fluid. Brake seal components couldbe damaged, causing partial or com

Automatic Transmission – If EquippedFluid Level CheckRegular automatic transmission fluid level checks are notrequired. For this reason, the dipstick

NOTE: The transmission must be in PARK before thebutton will operate. If equipped with a manual transmis-sion, the vehicle speed must be under 5 mph (

Selection of LubricantIt is important that the proper lubricant is used in thetransmission to assure optimum transmission perfor-mance. Use only manuf

Appearance Care and Protection from CorrosionProtection of Body and Paint from CorrosionVehicle body care requirements vary according to geo-graphic l

•Use a high quality cleaner wax, such as MOPAR威Cleaner Wax or equivalent to remove road film, stainsand to protect your paint finish. Take care never

•If you carry special cargo such as chemicals, fertilizers,de-icer salt, etc., be sure that such materials are wellpackaged and sealed.•If a lot of dr

•For grease stains, apply MOPAR威 Multi-PurposeCleaner or equivalent to a clean, damp cloth andremove the stain. Use a fresh, damp towel to removesoap

Cleaning HeadlightsYour vehicle has plastic headlights that are lighter andless susceptible to stone breakage than glass headlights.Plastic is not as

Seat Belt MaintenanceDo not bleach, dye, or clean the belts with chemicalsolvents or abrasive cleaners. This will weaken the fabric.Sun damage can als

CAUTION!•When installing the integrated power modulecover, it is important to ensure the cover is prop-erly positioned and fully latched. Failure to d

Cavity Car-tridgeFuseMini-FuseDescription9 ———10 30 AmpPink— Windshield Wiper11 30 AmpPink— Anti-Lock Brake System(ABS) Valves12 40 AmpGreen— Radiator

Rear Power Distribution CenterThere is also a power distribution center located in thetrunk under the spare tire access panel. This centercontains fus

Trunk Emergency ReleaseThe trunk of your vehicle is equipped with an emergencyrelease handle. It is located on the inside of the trunk lid,near the la

CAUTION!•When installing the power distribution centercover, it is important to ensure the cover is prop-erly positioned and fully latched. Failure to

Cavity Car-tridgeFuseMini-FuseDescription5 30 AmpPink— Heated Seats – IfEquipped6 — 20 AmpYellowFuel Pump7 — 15 AmpBlueSub Amp – If Equipped8 — 15 Amp

Cavity Car-tridgeFuseMini-FuseDescription23———24———25———26———27 — 10 AmpRedOccupant Restraint Con-troller (ORC)28 — 10 AmpRedIgnition Run, AC HeaterCo

Cavity Car-tridgeFuseMini-FuseDescription38 — 10 AmpRedCargo Light/Vehicle In-formation Module – IfEquipped39 — 10 AmpRedHeated Mirrors – IfEquipped40

in the fresh air and high blower setting. This willensure adequate system lubrication to minimize thepossibility of compressor damage when the system

BULB REPLACEMENTLow Beam Headlamp, High Beam Headlamp,Park/Turn Lamp — Models with HalogenHeadlamps — If EquippedSee your authorized dealer for bulb r

NOTE:•If a screwdriver is used, make sure a soft material isplaced between the vehicle body and tool so not toscratch the paint.2. Rotate the bulb’s s

3. Remove the fasteners from the back of the tail lampassembly.4. Pull back the trunk liner.5. Remove the remaining fasteners from the back of thetail

9. Turn the appropriate bulb and socket assembly coun-terclockwise to remove it from the tail lamp assembly.10. Disconnect the bulb from the socket as

Center High-Mounted Stop Lamp (CHMSL)The CHMSL uses LED lamps that are not serviceableseparately. The CHMSL must be replaced as an assembly,see your a

If you will be carrying children too small for adult-sizedseat belts, the seat belts or the Lower Anchors and Tetherfor CHildren (LATCH) feature also

FLUID CAPACITIESU.S. MetricFuel (Approximate) 19 Gallons 72 LitersEngine Oil with Filter6.1 Liter Engine (SAE 5W-40, API Certified) 7 Quarts 6.6 Liter

FLUIDS, LUBRICANTS, AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile For

ChassisComponent Fluid, Lubricant, or Genuine PartManual Transmission – If Equipped MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensedA

MAINTENANCE SCHEDULESCONTENTS䡵 Emission Control System Maintenance ... 392䡵 Maintenance Schedule ... 392▫ Required Maintenance Inter

EMISSION CONTROL SYSTEM MAINTENANCEThe Scheduled Maintenance services listed in bold type,must be done at the times or mileages specified to ensurethe

NOTE:•The oil change indicator message will not monitor thetime since the last oil change. Change your vehicle’soil if it has been six months since yo

•Check the fluid levels of the coolant reservoir, brakemaster cylinder, and power steering, and add asneeded.•Check all lights and other electrical it

6,000 Miles (10,000 km) or6 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepair

18,000 Miles (30,000 km) or18 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Inspect the rear axle fl

30,000 Miles (50,000 km) or30 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Replace the engine air c

of ejection and the risk of injury caused by striking theinside of the vehicle. Everyone in a motor vehicle shouldbe belted at all times.Lap/Shoulder

42,000 Miles (70,000 km) or42 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepai

48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule❏ Change the engine oil and engine oil filter.❏ Rotate tires.❏ If you are using your

54,000 Miles (90,000 km) or54 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Inspect the rear axle fl

66,000 Miles (110,000 km) or66 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepa

78,000 Miles (130,000 km) or78 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepa

90,000 Miles (150,000 km) or90 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Replace the engine air

102,000 Miles (170,000 km) or102 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Replace the spark plu

114,000 Miles (190,000 km) or114 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRe

126,000 Miles (210,000 km) or126 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Inspect the rear axle

138,000 Miles (230,000 km) or138 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRe

WARNING! (Continued)•Wearing your belt in the wrong place could makeyour injuries in an accident much worse. Youmight suffer internal injuries, or you

144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule❏ Change the engine oil and engine oil filter.❏ Rotate tires.❏ If you are using y

* This maintenance is recommended by the manufacturerto the owner, but is not required to maintain emissionswarranty.WARNING!•You can be badly injured

IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 Suggestions For Obtaining Service For YourVehicle... 413▫ Prepare For The Appointm

䡵 Publication Order Forms ... 417䡵 Department Of Transportation Uniform TireQuality Grades ... 419▫ Treadwear ...

SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you’re having warranty work done, be sure to have theright papers with

This is why you should always talk to an authorizeddealer’s service manager first. Most matters can be re-solved with this process.•If for some reason

Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY)To assist customers who have hearing difficulties, themanufacturer has installed specia

We appreciate that you have made a major investmentwhen you purchased the vehicle. An authorized dealerhas also made a major investment in facilities,

If NHTSA receives similar complaints, it may open aninvestigation, and if it finds that a safety defect exists ina group of vehicles, it may order a r

3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.”WARNING!•A belt that is buckled into the wrong

LLC vehicles. A complete working knowledge of thevehicle, system, and/or components is written instraightforward language with illustrations, diagrams

DEPARTMENT OF TRANSPORTATION UNIFORMTIRE QUALITY GRADESThe following tire grading categories were established bythe National Highway Traffic Safety Ad

Temperature GradesThe temperature grades are A (the highest), B, and C,representing the tire’s resistance to the generation of heatand its ability to

INDEX10

About Your Brakes ...271,274ABS (Anti-Lock Brake System) ... 274,277Adding Engine Coolant (Antifreeze) ...360Adding F

Automatic Headlights ...129Automatic TransaxleSpecial Additives ... 368Automatic Transmission ... 260

Bulbs, Light ... 76,382Calibration, Compass ...186Capacities, Fluid ...388Caps, FillerFu

Console, Overhead ...141Contract, Service ... 415Coolant Pressure Cap (Radiator Cap) ... 361Cooling Sy

Door Locks, Automatic ...31Door Opener, Garage ...142DrivingOn Slippery Surfaces ... 265Through Flo

Oil Change Interval ...348Oil Filler Cap ... 349Oil Filter ...350Oil Filter Disposal .

WARNING! (Continued)•A belt that is worn under your arm is dangerous.Your body could strike the inside surfaces of thevehicle in an accident, increasi

Fluids ...389Fluids, Lubricants and Genuine Parts ...389Fog Lights ... 130,169Folding Rear

GVWR ... 318Hands-Free Phone (Uconnect™) ... 85HazardDriving Through Flowing, Rising, or Shallow Stand-ing Wate

Instrument Cluster ...163,164Instrument Panel and Controls ... 162Instrument Panel Lens Cleaning ...373Integrate

Brake Assist Warning ...285Brake Warning ... 170,274Bulb Replacement ... 382,383Center Mounted Stop

Theft Alarm (Security Alarm) ... 171Tire Pressure Monitoring (TPMS) ... 171,305Traction Control ...285Turn Signal

Electric Remote ...83Exterior Folding ... 82Heated ... 83Outside ...

Overhead Console ... 141Overheating, Engine ...322Owner’s Manual (Operator Manual) ... 4,417Paint Care ..

Rear Seat, Folding ... 126Rear Window Defroster ...157Rear Window Features ...157Recorder, Event

Seat Belts ... 36,38,74And Pregnant Women ... 47Child Restraint ... 62,63,64,70Extender ...

Automatic Transmission ... 255,260Shoulder Belts ...38Side Window Demisters (Defrosters) ... 237Signals, Tur

5. Position the shoulder belt on your chest so that it iscomfortable and not resting on your neck. The retractorwill withdraw any slack in the belt.6.

System, Remote Starting ...27Tachometer ...164Telescoping Steering Column ...136Temperature Gaug

Disabled Vehicle ... 339Recreational ... 319Towing Assistance ... 100Towing Vehicle Beh

Vehicle Storage ...236,381Vehicle Theft Alarm (Security Alarm) ...18Viscosity, Engine Oil ... 349Voice R

291686.ps 11Y532-126-AA Chrysler 1" gutter 07/14/2010 08:26:13VEHICLES SOLD IN CANADAWith respect to any Vehicles Sold in Canada, the nameChrysle

Chrysler Group LLC10D492-126-AD 4th EditionPrinted in U.S.A.

Lap/Shoulder Belt Untwisting ProcedureUse the following procedure to untwist a twisted lap/shoulder belt.1. Position the latch plate as close as possi

How To Disengage The Automatic Locking ModeUnbuckle the combination lap/shoulder belt and allow itto retract completely to disengage the Automatic Loc

NOTE: These devices are not a substitute for proper seatbelt placement by the occupant. The seat belt still must beworn snugly and positioned properly

BeltAlert威 ProgrammingThe BeltAlert威 can be enabled or disabled by yourauthorized dealer or by performing the following steps:NOTE: Chrysler Group LLC

Seat Belts and Pregnant WomenWe recommend that pregnant women use the seat beltsthroughout their pregnancy. Keeping the mother safe isthe best way to

INTRODUCTIONCONTENTS䡵 Introduction ... 4䡵 How To Use This Manual ... 4䡵 Warnings And Cautions ...

Supplemental Restraint System (SRS) - AirbagsThis vehicle has Advanced Front Airbags for both thedriver and front passenger as a supplement to the sea

The Advanced Front Airbags have a multistage inflatordesign. This allows the airbag to have different rates ofinflation based on the severity and type

•Supplemental Side Airbag Inflatable Curtains (SABIC)•Front and Side Impact Sensors•Front Seat Belt Pretensioners, Seat Belt Buckle Switch,and Seat Tr

WARNING! (Continued)•Do not mount any accessories to the knee bolstersuch as alarm lights, stereos, citizen band radios,etc.Supplemental Side Airbag I

•Being too close to the SABIC airbags during deploy-ment could cause you to be severely injured or killed.The system includes side impact sensors adja

WARNING!Infants in rear-facing child restraints should neverride in the front seat of a vehicle with a passengerAdvanced Front Airbag. An airbag deplo

Do not lean against the door or window. If your vehiclehas side airbags, and deployment occurs, the side airbagswill inflate forcefully into the space

The ORC determines if deployment of the front and/orside airbags in a frontal or side collision is required.Based on the impact sensors signals, a cen

position, in the ACC position, or not in the ignition, theairbag system is not on and the airbags will not inflate.The ORC contains a backup power sup

wheel hub trim cover and the upper right side of theinstrument panel separate and fold out of the way as theairbags inflate to their full size. The ai

INTRODUCTIONCongratulations on selecting your new Chrysler GroupLLC vehicle. Be assured that it represents precisionworkmanship, distinctive styling,

Front and Side Impact SensorsIn front and side impacts, impact sensors can aid theORC in determining appropriate response to impactevents. Additional

floor. They are not caused by contact with chemicals.They are not permanent and normally heal quickly.However, if you haven’t healed significantly wit

Maintaining Your Airbag SystemWARNING!•Modifications to any part of the airbag systemcould cause it to fail when you need it. You couldbe injured if t

Airbag Warning LightYou will want to have the airbags ready toinflate for your protection in a collision. Theairbag system is designed to be maintenan

•How far (if at all) the driver was depressing theaccelerator and/or brake pedal; and,•How fast the vehicle was traveling.These data can help provide

WARNING!In an collision, an unrestrained child, even a tinybaby, can become a projectile inside the vehicle. Theforce required to hold even an infant

WARNING!Rearward-facing child seats must never be used inthe front seat of a vehicle with the front passengerairbag unless the airbag is turned off. A

•Check belt fit periodically. A child’s squirming orslouching can move the belt out of position.•If the shoulder belt contacts the face or neck, move

Here are some tips on getting the most out of your childrestraint:•Before buying any restraint system, make sure that ithas a label certifying that it

available for some time. For some older child restraints,many child restraint manufacturers offer add-on tetherstrap kits or retrofit kits. You are ur

1INTRODUCTION 5

Installing the LATCH-Compatible Child RestraintSystemWe urge you to follow the manufacturer’s directionscarefully when installing your child restraint

provide the most direct path between the anchor and thechild restraint. Finally, tighten all three straps as youpush the child restraint rearward and

Installing Child Restraints Using the Vehicle SeatBeltThe seat belts in the passenger seating positions areequipped with either an Automatic Locking R

3. Attach the tether strap hook (A) of the child restraint tothe anchor (B) and remove slack in the tether strapaccording to the child restraint manuf

While cruising, brief full-throttle acceleration within thelimits of local traffic laws contributes to a good break-in.However, wide-open throttle acc

WARNING! (Continued)•Do not allow people to ride in any area of yourvehicle that is not equipped with seats and seatbelts.•Be sure everyone in your ve

damaged, have a competent mechanic inspect the com-plete exhaust system and adjacent body areas for broken,damaged, deteriorated, or mispositioned par

they cannot slip out of position and interfere with thepedals or impair safe operation of your vehicle in otherways.WARNING!Pedals that cannot move fr

WARNING! (Continued)Failure to properly follow floor mat installation ormounting can cause interference with the brakepedal and accelerator pedal oper

UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 Mirrors ... 81▫ Automatic Dimming Mirror ... 81▫ Outside Mir

WARNINGS AND CAUTIONSThis Owner’s Manual contains WARNINGS against op-erating procedures that could result in a collision orbodily injury. It also con

▫ Voice Command System Operation ... 114▫ Commands ... 116▫ Voice Training ... 119䡵 Seats ...

▫ Overhead Console Map/Reading Lights ... 132▫ Interior Lights ... 133䡵 Windshield Wipers And Washers ... 134▫ Intermittent

▫ Troubleshooting Tips ... 147▫ General Information ... 148䡵 Power Sunroof — If Equipped ... 148▫ Opening Sunro

MIRRORSAutomatic Dimming MirrorThis mirror automatically adjusts for headlight glarefrom vehicles behind you. You can turn the feature on oroff by pre

Outside MirrorsTo receive maximum benefit, adjust the outside mirror(s)to center on the adjacent lane of traffic and a slightoverlap of the view obtai

Power MirrorsThe power mirror switch is located on the driver’s doortrim panel next to the power door lock switch. A rotaryknob selects the left mirro

Illuminated Vanity MirrorsAn illuminated vanity mirror is located on the sun visor.To use the mirror, rotate the sun visor downward andswing the mirro

Uconnect™ Phone — IF EQUIPPEDUconnect™ Phone is a voice-activated, hands-free, in-vehicle communications system. Uconnect™ Phone al-lows you to dial a

Uconnect™ Phone allows you to transfer calls betweenthe system and your cellular phone as you enter or exityour vehicle and enables you to mute the sy

The Uconnect™ Phone can be used with any Hands-FreeProfile certified Bluetooth威 cellular phone. See theUconnect™ website for supported phones. If your

VEHICLE MODIFICATIONS/ALTERATIONSWARNING!Any modifications or alterations to this vehicle couldseriously affect its roadworthiness and safety andmay l

⬙Phonebook⬙ and ⬙New Entry.⬙ Please remember, theUconnect™ Phone works best when you talk in anormal conversational tone, as if speaking to someonesit

The following are general phone to Uconnect™ Phonepairing instructions:•Press the button to begin.•After the ⬙Ready⬙ prompt and the following beep, sa

Dial by Saying a Number•Press the button to begin.•After the ⬙Ready⬙ prompt and the following beep, say⬙Dial.⬙•The system will prompt you to say the n

•After the ⬙Ready⬙ prompt and the following beep, say⬙Phonebook New Entry.⬙•When prompted, say the name of the new entry. Use oflong names helps the V

•Automatic download and update, if supported, beginsas soon as the Bluetooth威 wireless phone connection ismade to the Uconnect™ Phone, for example, af

NOTE:•The phone handset must support Bluetooth威 OBEXtransfers of phonebook entries to use this feature.•Some phones cannot send phonebook entries if t

After you are finished editing an entry in the phonebook,you will be given the opportunity to edit another entry inthe phonebook, call the number you

Delete/Erase “All” Uconnect™ Phonebook Entries•Press the button to begin.•After the ⬙Ready⬙ prompt and the following beep, say⬙Phonebook Erase All.⬙•T

Phone Call FeaturesThe following features can be accessed through theUconnect™ Phone if the feature(s) are available on yourcellular service plan. For

in progress. To go back to the first call, refer to ⬙TogglingBetween Calls⬙ in this section. To combine two calls, referto ⬙Conference Call⬙ in this s